Dd-technologies LokkLatch Round User Manual download pdf

1. Determine the desired height of the latch on the gate. Hold the latch in place on

the post and close the gate.

2. Position the Striker Body “C” on the gate frame by engaging the striker bolt

into the latching tongue. (Check whether the adaptor shim ‘S

’ needs to be

applied to ﬁt your gate frame.) When all latch

components are aligned correctly, use the pencil to mark inside the four ﬁxing

slots of the Striker Body “C”.

3. Place all latch components aside and drill a pilot hole in the center of the

marked slots using a

/64" (4.5mm) drill-bit. Remember that centering the

screws inside the slots allows future adjustment for gate sag.

4. Secure the Striker Body “C” ﬁrmly onto the gate frame using four of the large

hex-head Tek screws supplied.

5. Open the gate. Place the Latch Assembly back onto the latch post and then close

the gate. Engage the Striker Bolt through the latch tongue again, aligning the main

Latch Body on the latch post so that the Striker Bolt will close in the center of the latch

tongue (the Rivet marks the center of the latching zone).

6. Hold the Latch Assembly in place and mark the post through the two main screw-

ﬁxing holes at the side of the Round Post Bracket.

INSTALLING THE

ROUND POST BRACKET

Once the “handing” is determined,

insert the Round Post Bracket into

the back of the latch body at a

slight angle, as shown: rotate the

Post Bracket in the direction of

the arrows until it snaps ﬁrmly in

alignment on the latch body. Insert

a single short screw (Screw 1) in the

center hole inside the bracket, and

a short screw top and bottom

(screws 2 & 3) of the latch.

Round Post

Bracket

Key

Tongue

FENCE

POST

GATE

FRAME

LATCH

BODY

STRIKER

BODY

Striker

Bolt

Release

Knob

Round Post

Bracket

INSTALLATION PROCEDURE

• This latch is designed to be tted to the “opening” side of the gate. See

notes at right re right- or left-hand installation, and also for the tting of the

Round Post Bracket (A) to the Latch Body ➧ ➧ ➧

Post sizes: 1

/8–2", 2

/8", 2

/8" (48–51mm, 60mm, 73mm).

Gate frame sizes: 1

/8" and 1

/8" (35mm and 41mm).

Gap Variance: 1" -2

/4" (25mm - 57mm)

Tools: Electric or cordless drill (use low clutch settings), Phillips No.1

screwdriver,

/16" hex-head (Tek) drill drive (for use in electric/cordless drill),

/64" [4.5mm] drillbit for pre-drilling metal.

INSTALLATION NOTES & PROCEDURE

• This latch is designed, ideally, to be tted to the inside (i.e. house or tennis court side) of the gate. If

installing to the outside (i.e. street side) of the gate ensure there is hand access to operate the latch…or, if

this pack contains an “EXTERNAL ACCESS KIT”, ensure it is ﬁxed to this latch before installing the entire latch

onto the gate (see over for details).

• For 2

/8" (51mm) fence posts and 1

/8" (41mm) gate frames, no adapters are required.

This latch kit includes special adapter shims for ﬁtting the latch to posts and gate frames of varying diameters (see S1, S2

& S3). The adapters have the diameter they are designed for molded into them. If required, place two identical adapters

(S1 or S2) into their corresponding

positions on the inside the Round Post Bracket facing the Fence Post.

For LokkLatch only installation , follow Step #1

†

STEP #1 — MAIN LATCH BODY

Rivet

Latch Body

Screw 1

Screw 2

Screw 3

7. Remove the Latch Assembly and drill the pilot holes where marked.

8. Secure the Latch Assembly using the two remaining hex-head Tek screws supplied.

9. Check latch operation to ensure smooth, reliable latching. Your LOKKLATCH is now ready for use.

NB: If this pack does not have an “External Access Kit”, you can purchase one from your supplier.

STEP #2 — EXTERNAL ACCESS KIT

For latch with External Access Kit , follow Step #1, then Step #2

†

For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY,

go to our website at www.ddtechglobal.com

LLINSTR0028PA •instr_LLABRND_1 11 11

(Note: Locking the External Access Assembly only locks the Push Button. It does not lock the Latch Body, which is lockable separately.)

RIVET

Horizontal

Locate

Push Rod

into hole

Fixing

Shroud

Push Button

housing

Release

Knob

Release

Knob

Push rod

Large return

Small

return

The External Access Kit (EAK) allows a gate to be

opened and locked from the opposite side to the latch.

The EAK is connected to the Latch Body by a Push Rod.

INSTALLATION PROCEDURE

1. With the latch in the unlocked position, prop the gate

open. Slide the Release Knob to the up position at the

rear of the Latch Body. Take the Push Rod and, holding

it vertically, slide the Large Return through the slot in the

side of the Latch Body as shown in diagram 1. Be sure the Large Return

protrudes completely through to the other side of the Latch Body.

2. Lower the Release Knob to the down position so that it encloses the Large

Return of the Push Rod. Turn the key to lock the Release Knob in place.

Rotate the Push Rod to the horizontal position as shown in diagram 2.

3. To aid with installation, the Push Button is locked. Place the Push Button Assembly

against the opposite side of the Round Post Bracket from the Latch Body.

Place the Small Return of the Push Rod into the hole on the side of the

Push Button as shown in diagrams 3 & 4.

4. With the Small Return of the Push Rod ﬁrmly inside the hole on the Push

Button, slide the Fixing Shroud over the Push Button until the Fixing Shroud

sits ﬁrmly into the corresponding Round Post Bracket molding (see diagram 5).

This will leave the Push Rod at a slight angle, which is normal.

5. Secure the Fixing Shroud to the Round Post Bracket with the four small screws

using the Phillips No. 1 screwdriver. Unlock the Push Button and check for smooth

operation. The External Access Kit is now ready for use.

FOR ROUND POST AND GATE FRAME

www.ddtechglobal.com

AUSTRALIA: Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086

USA: 7731 Woodwind Drive, Huntington Beach, CA 92647

1 2

Summary of Contents

Page 1

1. Determine the desired height of the latch on the gate. Hold the latch in place on the post and close the gate.2. Position the Striker Body “C” on t

Page 2

PROCEDIMIENTOS DE INSTALACIÓNEste cerrojo está diseñado para encajar en el lado de “abertura” de la puerta o portón. Ver las notas a la derecha sobr

Comments to this Manuals

No comments

Dd-technologies LokkLatch Round User Manual

Browse online or download User Manual for For Home Dd-technologies LokkLatch Round. D&D Technologies LokkLatch Round User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For Home Dd-technologies LokkLatch Round